Blogs

Home / Blogs / Blogs / 722.9 VGS No Communication: When Is a Complete EHS Required?

722.9 VGS No Communication: When Is a Complete EHS Required?

Views: 4     Author: Site Editor     Publish Time: 2026-11-06      Origin: Site

facebook sharing button
twitter sharing button
line sharing button
wechat sharing button
linkedin sharing button
pinterest sharing button
whatsapp sharing button
sharethis sharing button

MERCEDES-BENZ 722.9 · VGS / EHS IDENTIFICATION

A Mercedes-Benz 722.9 VGS communication failure does not automatically justify replacing a standalone control unit or the complete gearbox. The correct replacement depends on the result of the specified diagnostic checks, the original EHS identification and, where applicable, the valve body plate configuration and EHS generation recorded in VeDoc.

DIRECT ANSWER

Under Mercedes-Benz XENTRY procedure LI27.19-P-072588, if the specified checks have been completed and communication with the original VGS still cannot be established, the complete electrohydraulic controller unit (EHS) must be replaced. A VGS repair kit is not permitted for this particular condition because the necessary valve characteristics cannot be transferred from the original control unit.

1. When Does a 722.9 VGS Fault Require a Complete EHS?

Mercedes-Benz XENTRY document LI27.19-P-072588, Version 3, dated September 16, 2025, addresses cases where transmission control unit Y3/8n4 (Fully Integrated Transmission Control Unit, VGS) is not listed in the diagnostic quick test or cannot establish communication.

For the 722.9 application, the bulletin does not instruct technicians to replace the VGS immediately. It establishes a sequence that must be completed before a component replacement decision is made.

  1. Process the referenced electrical-system procedure

    Complete the checks required by Mercedes-Benz document LI54.15-P-057373 before replacing any component parts.

  2. Perform the VGS ignition reset

    After completing the referenced procedure, perform the specified ignition reset on transmission control unit Y3/8n4.

  3. Inspect the transmission connector

    Check for loose connections, damaged wiring, damaged pins and other connector-related concerns.

  4. Confirm whether VGS communication is restored

    If communication still cannot be established after the specified checks, the complete EHS must be replaced under this procedure. A VGS repair kit is not permitted for this condition.

Important application boundary

This is a specific manufacturer procedure, not a rule that every 722.9 transmission warning or VGS fault requires a complete EHS. The bulletin also states that diagnosis must be evaluated on a case-by-case basis by trained professional technicians using the appropriate manufacturer tools and procedures.

2. Why Is a VGS Repair Kit Not an Alternative in This Situation?

The distinction is the availability of the original control unit's valve characteristics.

In the no-communication condition covered by LI27.19-P-072588, the original VGS cannot provide the necessary valve characteristics for transfer to the replacement control unit.

This is why Mercedes-Benz specifies the complete electrohydraulic controller unit (EHS), rather than an individual VGS repair kit, once the required diagnostic checks have been completed and communication remains unavailable.

The distinction is important when comparing parts quotations. A standalone VGS control component and a complete EHS assembly are not equivalent supply items, even if both are described in a parts listing as 722.9 electronic or mechatronic components.

3. How Is the Correct Replacement EHS Identified?

A second Mercedes-Benz document, LI27.19-P-074985, Version 3, dated July 15, 2025, addresses a different problem: commissioning cannot be completed after replacement of a 722.9 transmission, EHS or VGS repair kit.

The bulletin identifies an incorrect older EHS A-code (Generation EHS) in VeDoc as a possible cause for the newly installed transmission or control assembly.

PATH A · DIAGNOSIS AVAILABLE

Read the EHS part number through XENTRY

In XENTRY Diagnostics, use Control Unit View → Current Quick Test → Fully Integrated Transmission Control → EHS Part Number.

The bulletin instructs the technician to order the replacement EHS using the part number read from the currently installed hardware.

PATH B · DIAGNOSIS UNAVAILABLE

Read the identification from the EHS itself

If vehicle diagnosis is no longer possible, the number must be read directly from the physical EHS.

The ordering process should be initiated using that identification, subject to the specific exceptions and application rules in the bulletin.

The important purchasing principle is that the original installed EHS identity is more useful than a broad description such as "722.9 VGS3".

VGS2 and VGS3 hardware identification examples

LI27.19-P-074985 lists the following hardware identifiers as examples from the diagnostic quick test:

OLDER HARDWARE · VGS2 A0335457332

VGS2 hardware identification shown in the bulletin.

NEWER HARDWARE · VGS3 A0034460310

VGS3 hardware identification shown in the bulletin.

NEWER HARDWARE · VGS3 A0009018008

Another VGS3 hardware identification shown in the bulletin.

These are diagnostic hardware identifiers, not universal replacement EHS part numbers.

They help distinguish the hardware generations described in the service information. They must not be used alone to approve an EHS order or a direct VGS2-to-VGS3 interchange.

4. Why Can the Same Old EHS Number Lead to Different Replacement Parts?

This is one of the most important details in Mercedes-Benz document LI27.19-P-074985.

The bulletin lists different replacement EHS numbers according to the original valve body plate configuration and the old EHS A-code recorded in VeDoc.

Documented example: Original EHS A2202701206

The same original EHS number appears in three different VGS3 configurations. Each configuration leads to a different replacement EHS number and a different new A-code.

Original valve body plate Old A-code Original EHS number Specified replacement EHS New A-code
J Plate A28 / A29 A2202701206 A2202702706 A92
O Plate A45 A2202701206 A2202702906 A94
N Plate A39 A2202701206 A2202703106 A95

The three rows above are specific VGS3 service mappings documented by Mercedes-Benz. The full bulletin also lists other valve body plate configurations, including P, M and K, with their own identification and A-code requirements.

For the J Plate example, the old A-code A28/A29 is deleted and A92 is documented in VeDoc. For the O Plate and N Plate examples, the corresponding new codes are A94 and A95.

Do not use this table as a universal supersession chart.

The replacement number depends on the documented combination of original EHS number, valve body plate and old A-code. The full manufacturer procedure must be checked before ordering or updating vehicle records.

A specific engine 629 exception

The same bulletin identifies an additional exception for engine 629 with a 722.9 transmission, specifying EHS A2202702406.

It also gives a narrower procedure for models 219.356 and 171.456 with transmission 722.906 up to and including model year 2005 (code 805): where the read-off number is A2202701206, that number is no longer available, and the bulletin specifies EHS A2202702706 with A92 documented in VeDoc.

These exceptions must be assessed against the exact vehicle and transmission identification. They should not be combined with the general three-row mapping above or applied to other 722.9 configurations without verification.

5. VGS Cannot Communicate vs Commissioning Cannot Be Completed

These are two different technical situations, covered by separate Mercedes-Benz procedures. They should not be treated as one fault or one replacement decision.

LI27.19-P-072588

Original VGS communication failure

Problem: Y3/8n4 is not listed in the quick test or communication cannot be established.

Required sequence: Complete the referenced procedure, ignition reset and connector inspection.

Replacement decision: If communication remains unavailable, replace the complete EHS under the bulletin.

LI27.19-P-074985

Commissioning failure after replacement

Problem: Commissioning cannot be completed after replacing the 722.9 transmission, EHS or VGS repair kit.

Possible cause: An incorrect older EHS A-code remains documented in VeDoc.

Required action: Identify the correct EHS and update the A-code according to the applicable manufacturer procedure.

The first situation concerns communication with the original control unit and the ability to transfer valve characteristics. The second concerns the identification and documentation of the newly installed EHS generation.

A new EHS that cannot complete commissioning should not automatically be classified as defective. The current hardware identity and corresponding VeDoc information must also be considered.

6. What Information Should Be Confirmed Before Ordering a 722.9 VGS or EHS?

A 722.9 parts enquiry should identify the component actually required, not just the transmission family. The following information helps distinguish an individual control unit from a complete EHS assembly and reduces the risk of selecting the wrong replacement.

Information What to provide What it helps establish
Gearbox identification Full 722.9 transmission code, including the applicable variant. The transmission application.
Original EHS number Complete number from XENTRY or the physical EHS label. The installed hydraulic-electronic assembly identity.
Valve body plate J, O, N or other identifiable plate configuration. The applicable service replacement mapping.
Old EHS A-code Existing EHS generation code recorded in the relevant vehicle documentation. The documented replacement and commissioning configuration.
VGS hardware identity Diagnostic hardware identification, where available. The control-unit generation and current hardware configuration.
Communication status Whether the original VGS can communicate with the diagnostic system. Whether the no-communication procedure or replacement commissioning procedure is relevant.
Required supply scope VGS repair kit, individual control module, complete EHS or complete gearbox. The actual product required and the components that must be included.

Photographs that help with parts identification

  • A clear photograph of the original EHS identification label.
  • A photograph showing the complete valve body assembly.
  • A close-up of the valve body plate identification, where visible.
  • A clear view of the electrical connector and associated housing.
  • Diagnostic identification showing the EHS number and VGS hardware information, where available.

If the original transmission or EHS has previously been replaced, the identification of the currently installed hardware must also be considered. The vehicle's original factory configuration alone may not describe the actual assembly now fitted.

7. How Super5 Gearbox Distinguishes VGS and Complete EHS Supply

Super5 Gearbox supplies used and reconditioned complete gearbox assemblies and new transmission parts. For Mercedes-Benz 722.9 enquiries, a standalone transmission control component and a complete electrohydraulic controller unit are treated as different supply requirements.

A product described as a 722.9 control module should not automatically be interpreted as a complete EHS valve body assembly. The exact part reference, physical configuration and included components must be confirmed against the requested replacement.

For a VGS or EHS enquiry, provide the original EHS number, valve body plate identification, A-code where available, gearbox code and clear photographs. The required supply scope and availability can then be checked against the actual component specification.

If the requirement is for a complete 722.9 transmission rather than an individual control component, identify the complete gearbox variant and specify which associated components must be included.

Frequently Asked Questions

Does every Mercedes 722.9 VGS communication fault require a complete EHS?

No. Mercedes-Benz LI27.19-P-072588 specifies complete EHS replacement only after the required procedure, ignition reset and connector inspection have been completed and VGS communication still cannot be established. Other faults require their own diagnosis.

Can a VGS repair kit replace the complete EHS when the original VGS cannot communicate?

Not under the specific no-communication condition covered by LI27.19-P-072588. The necessary valve characteristics cannot be transferred from the original control unit, so the bulletin specifies the complete EHS.

Can the same 722.9 EHS part number have different replacement numbers?

Yes. Mercedes-Benz LI27.19-P-074985 documents different replacement EHS numbers for the same original number A2202701206 depending on the valve body plate and old A-code. The documented J, O and N Plate examples lead to A2202702706, A2202702906 and A2202703106 respectively.

How can I identify the correct replacement EHS if the vehicle cannot communicate with XENTRY?

The bulletin instructs technicians to read the number directly from the physical EHS when vehicle diagnosis is unavailable. Specific exceptions, including the engine 629 case, must also be checked against the complete procedure.

Are VGS2 and VGS3 hardware numbers sufficient for ordering a replacement EHS?

No. The hardware numbers distinguish the generations shown in the technical bulletin, but the replacement EHS must be identified using the relevant EHS part number, valve body configuration and applicable A-code information.

Does a 722.9 EHS commissioning failure mean the replacement part is faulty?

Not necessarily. LI27.19-P-074985 identifies an incorrect older EHS A-code in VeDoc as a possible cause. The current hardware and the corresponding EHS generation documentation should be checked before concluding that the new component is defective.

Technical References

Mercedes-Benz AG — XENTRY Tips, LI27.19-P-072588, Version 3, September 16, 2025. Y3/8n4 (VGS) not listed in quick test; no communication possible with VGS.

Mercedes-Benz AG — XENTRY Tips, LI27.19-P-074985, Version 3, July 15, 2025. Commissioning not possible after replacement of transmission 722.9, EHS or VGS repair kit.

LI54.15-P-057373 — Referenced electrical-system procedure required before component replacement in the applicable 722.9 no-communication procedure.

The part-number mappings and A-code examples in this article apply only to the configurations specified in the relevant Mercedes-Benz documentation. Confirm the latest vehicle-specific service information before ordering or installing replacement components.

Leave a Message
Contact Us

Find A Gearbox

Products

Quick Links

Copyright © 2026 Super5 Auto All Rights Reserved. Sitemap | Privacy Policy